娛樂滿紛 26FUN - Powered by Discuz! Board

標題: 點ｆｏｒｍａｔ　部機呀？？ [打印本頁]

作者: ykl122 時間: 2005-6-10 01:38 PM 標題: 點ｆｏｒｍａｔ　部機呀？？

我想ｆｏｒｍａｔ個ｈａｒｄｄｉｓｋ呀
可否有人教我？？

作者: michaelwong71 時間: 2005-6-10 04:01 PM

Make a bootable disk with a PC running Windows 98, or Windows ME. Remember to copy the files of FDISK and FORMAT these two files to the 1.44 diskette. I cannot tell you the extension of these two files. Please check by yourselves.

Then, boot the PC with this diskette. Run FDISK, erase the partition first and make the partition again. Remember to press ESC to quit the FDISK program. Reboot again the PC. Type FORMAT C:/S. If it can see the drive C: then you get it.

作者: gaye 時間: 2005-6-10 05:49 PM

2000/XP/2003 用 CD boot 機就可以了

作者: vivienna 時間: 2005-6-10 06:22 PM

recently i hv started using ide--->usb interface to format hdd. it's a lot faster this way, but you will need more than one computer. it's good for people who are not familiar with running command in dos mode.

作者: gaye 時間: 2005-6-10 06:44 PM

Originally posted by vivienna at 2005-6-10 06:22 PM:
recently i hv started using ide---&...

如果有第二隻 HD boot 得到機 , 呢個方法好方便

作者: vivienna 時間: 2005-6-10 07:37 PM

Originally posted by gaye at 2005-6-10 06:44 PM:

如果有第二隻 HD boot 得到機 , 呢個方法好方便

i am using 'computer management' in windows to format the hdd

作者: jazzcat 時間: 2005-6-15 05:53 PM

using fdisk to setup what size you want for c: d: ....
do forget to setup c: as active otherwise it can not boot under dos after you format your HD
use command 'format c: /q /s' to format harddrive c, in quick and bootable mode.
or format c: /q
and use sys c:

作者: Xtravagant 時間: 2005-6-15 11:55 PM

Originally posted by gaye at 2005-6-10 06:44 PM:

如果有第二隻 HD boot 得到機 , 呢個方法好方便

可以講下點樣用法?

作者: vivienna 時間: 2005-6-16 12:07 AM

Originally posted by Xtravagant at 2005-6-15 11:55 PM:

可以講下點樣用法?

set bios to boot from usb device(if using IDE-USB) / or hdd (if using IDE) <---- i think i hv read this somewhere.

However, there is no need to use a 2nd hdd to boot, all you need is just a WIN start-up floppy disc.

If you need want to format, I have two choices for you:

1)use a windows start-up disk, and format in dos mode. but you will only get fat32 with this method.

2)if you are currently running a windows, plug in your USB drive first. Go to Control Panel, Performance and Maintenance, Administrative Tools, then Computer Management. To format any drive, just right click on the drive and choose format. If the drive is not yet partitioned, you can create partitions here.

如果你對於DOS唔熟悉﹐用IDE-USB ADAPTOR就最好。

歡迎光臨娛樂滿紛 26FUN (http://26fun.com/bbs/)